When you already know your camera and host receiver models, choose GMSL camera cables by matching the two endpoints first. For a 50 Ω coaxial link, confirm the connector series, keying code, and contact gender at each end. Then evaluate loss along each camera lane, check voltage drop if the system uses Power over Coax (PoC), and match the cable to its routing conditions.
Analog Devices' Gigabit Multimedia Serial Link (GMSL) is a serializer/deserializer (SerDes) communication architecture rather than a single plug standard. This guide focuses on 50 Ω coaxial GMSL and GMSL2 camera cable assemblies—walking through how to select a direct cable, an extension, or a 1-to-4 breakout harness without running into connector mismatches, signal reflections, or undervoltage dropouts.
How the coaxial cable fits into a GMSL camera link
In a GMSL camera link, the serializer chip inside the camera transmits high-speed video over the forward channel to the deserializer chip on the receiver side, while control data can travel back in the reverse direction across the same coaxial core. Where both ends of the link include compatible Power over Coax (PoC) injection and extraction circuitry, DC power is superimposed onto the same center conductor alongside the serialized data.
A passive coaxial cable only links a GMSL serializer port to a compatible GMSL deserializer port; it cannot adapt a camera directly into a raw MIPI CSI-2 or USB receptacle. A documented example is the StereoLabs ZED Link Mono capture card setup for the NVIDIA Jetson Orin Nano Developer Kit:

The host OS also requires matching board drivers and SDK software. Other platforms integrate the deserializer directly on the main board, but the coaxial cable always stays on the 50 Ω SerDes side of the chain.
According to the Analog Devices GMSL2 Hardware Design and Validation Guide (UG-2212 Rev 3), whether a link uses 50 Ω single-ended coaxial cable or 100 Ω shielded twisted pair (STP)—and whether a GMSL2 forward channel runs at 3 Gbps or 6 Gbps—depends on the specific SerDes devices and hardware configuration. Because 50 Ω coaxial and 100 Ω differential ports use different electrical terminations and footprints, their cables cannot be directly swapped on a given device port.
Matching connector families, keying and contact gender
Ordering the wrong connector end usually happens when a buyer treats "Mini FAKRA" as a single universal footprint, relies on plastic color alone to identify keying, or confuses panel-mount threads with electrical contact gender.
Standard FAKRA vs. quad Mini-coax families (HFM, MATE-AX)
Single-port GMSL cameras and capture cards frequently use standard FAKRA connectors, whereas multi-camera capture boards often consolidate four coaxial ports into a single 4-cavity Mini-coax footprint to save board edge space.
In cable catalogs, different high-density coaxial interfaces are often grouped together under the generic label "Mini FAKRA". For example, the Amphenol RF AUTOMATE Series guide (p. 4) distinguishes Type A (intermateable with HFM) from Type B (intermateable with MATE-AX), illustrating why two connectors labeled "Mini FAKRA", "Z-code", and "50 Ω" will not necessarily mate. Rather than relying on generic names or brand labels alone, confirm the exact interface type and mating part numbers in your capture card's hardware drawing.
EB-101-0587
Standard FAKRA · F–F
FAKRA Z jack to jack, with 1 m of 50 Ω RG174 cable. This configuration connects two male FAKRA Z ports.
View EB-101-0587
EB-014-0444
MATE-AX · quad jack
MATE-AX 4-port jack to four FAKRA Z jacks. 50 Ω RG174 cable; nominal assembly length: 200 cm.
Browse Mini FAKRA assemblies
EB-014-0766
HFM · quad plug
HFM 4-port plug to four FAKRA Z jacks. 50 Ω RG316D cable; nominal assembly length: 50 cm.
Browse Mini FAKRA assembliesTo select an assembly for your camera, match the mating interfaces and check the cavity-to-branch wiring map, length reference points and electrical ratings.
Mechanical keying (Z-code) vs. housing color
FAKRA and Mini-coax housings use mechanical keying profiles to prevent cross-plugging incompatible ports. Z-code denotes universal mechanical keying within that specific connector family. While Z-code is common on GMSL camera cables, it does not grant cross-family mechanical fit or electrical compatibility, and not every GMSL camera port is necessarily Z-code.
Standard FAKRA Z housings are commonly waterblue (while some vendor documentation, such as StereoLabs', describes a purple insert on its Z-code connectors). Treat housing color as a secondary visual check and specify the mechanical keying code explicitly when ordering.
Contact gender (male/plug vs. female/jack) across link topologies
Connector gender follows the manufacturer's contact and mating interface definition rather than whether a connector is panel-mounted on an enclosure:
- Male contact / plug: Contains the center pin (common on the camera receptacle).
- Female contact / jack: Contains the center socket that mates with the male pin (common on the camera-end cable connector).
When the camera uses a male FAKRA Z receptacle, the three standard harness roles map as follows:
| Configuration | Cable Ends | Typical Mating Role |
|---|---|---|
| Configuration1-to-1 Direct | Cable EndsFAKRA Z F-F (jack to jack) |
Typical Mating RoleConnects a male camera port directly to a single-channel male host port |
| ConfigurationIn-Line Extension | Cable EndsFAKRA Z M-F (plug to straight or 90° jack) |
Typical Mating RoleExtends an existing F-F cable or 1-to-4 branch to the camera |
| Configuration1-to-4 Breakout | Cable EndsQuad Mini-coax to 4× FAKRA Z jacks | Typical Mating RoleRoutes four host channels to individual camera connectors |
In the documented StereoLabs GMSL2 cable guide and ZED X cable support article, for instance, single-port hosts such as ZED Link Mono pair with an F-F cable, while multi-port hosts use a 1-to-4 quad Mini-to-FAKRA harness; always verify your actual capture card revision and mating part number before ordering.
Multi-camera 1-to-4 breakouts and cavity mapping
When a capture card uses a 4-in-1 quad connector, a passive 1-to-4 breakout cable fans out four separate point-to-point 50 Ω coaxial signal paths from one 4-cavity block to four individual FAKRA connectors. Separate channels do not mean isolated grounds.

Because the harness is passive, it cannot split one camera's video signal to four displays. Likewise, the cable itself does not merge video streams: deserialization—and, where supported by the active receiver hardware and system configuration, multi-camera frame synchronization or CSI stream aggregation—takes place on the active capture card or host unit.
When selecting or substituting a 1-to-4 harness, check two details:
- Cavity-to-branch wiring order: Each cavity inside the quad connector routes to one of the four FAKRA tails. If you use an off-the-shelf breakout without checking its wiring map against the host board's pinout, physical camera positions may not match the software channel order assigned by your system configuration.
- Partial port population: A 4-branch harness or multi-port capture card does not require all four branches to be connected in every operating mode. Secure any unpopulated FAKRA ends and cover them with appropriate protective caps to keep out dust and prevent mechanical rattling.
Channel length, attenuation and per-lane calculation
Because GMSL2 links operate at 3 Gbps or 6 Gbps over a single coaxial core, maximum cable length has no universal single number—it is determined jointly by your SerDes devices, PCB design, cable attenuation, and connector transitions.
Why DC–3 GHz or DC–6 GHz labels do not define reach
A catalog frequency label such as DC–3 GHz or DC–6 GHz does not guarantee that a cable assembly will pass 3 Gbps or 6 Gbps GMSL2 data at any arbitrary length. As detailed in ADI UG-2212 Rev 3 and the ADI GMSL2 Channel Specification (Rev 1), the SerDes transmitter and receiver pins form the active endpoints of the link, while the complete passive channel between those pins encompasses the serializer and deserializer PCB traces, passive components, board-mount connectors, cable assembly, and any in-line couplings.

Two key channel checks are insertion loss (signal attenuation across frequency) and return loss (a measure of reflected signal energy). For multi-cable bundles, validation also needs to account for crosstalk between adjacent links. High-frequency attenuation cannot be judged from outer cable diameter or cable type names alone; conductor construction, dielectric material, shielding structure, and crimp termination quality all shape the loss curve. In addition, every in-line M-F extension joint adds a contact pair, insertion loss, and a local impedance discontinuity that consumes channel margin. Whenever possible, use a single continuous cable rather than chaining extensions.
Calculate length along one camera lane
In a multi-camera breakout setup, signal loss and DC resistance accumulate in series along each individual camera lane, not across all four branches combined.

To see how a per-lane figure compares against an OEM system limit, StereoLabs' GMSL2 cable documentation specifies a maximum total link length of 15 m (49 ft) from host connector to camera—explicitly including the 0.5 m 1-to-4 breakout segment—for its documented cable assemblies. While a 5.5 m per-lane path satisfies a 15 m geometric limit, meeting the length number satisfies only one condition. Whether any specific cable combination locks reliably at 3 Gbps or 6 Gbps still depends on verifying that the assembly's actual insertion loss, coupling reflection, connector mating, and DC resistance meet your target system's channel budget.
Power over Coax (PoC): loop resistance and voltage-drop budget
A passive coaxial cable does not generate or regulate PoC; it conducts DC power between a compatible PoC injection network on the host side and an extraction network on the camera side (ADI UG-2212 Rev 3, p. 3; TI SNLA224B, Revised Oct 2025).
Simply verifying metallic DC continuity from end to end is not enough for PoC. Both the coaxial cable and all mated connectors or couplings must have an uninterrupted DC path (no blocking capacitors), adequate current and voltage ratings, and low enough DC loop resistance to keep the voltage arriving at the camera within specification.

Calculating passive loop voltage drop
Never use the cable's 50 Ω high-frequency characteristic impedance to calculate DC voltage drop. For DC power, current flows out along the center conductor, returns along the outer coaxial shield, and crosses the mated connector and coupling contacts. The passive cable assembly's contribution to DC voltage drop is:

Here, Rcenter and Rshield depend on the specific conductor cross-section, material, cable length, and operating temperature, while any voltage drop across board-level PoC filter inductors or protection components must be budgeted separately.
HYPOTHETICAL OPERATING POINT
12.0 VMinimum at the host injection point
2.0 ΩAssumed cable + contact loop limit
0.50 ACamera current at this operating point
Cable drop: 0.50 A × 2.0 Ω = 1.0 V
0.5 V below the required minimum. This example fails the voltage check even if the signal channel meets its length limit.
When running this check on your own hardware, apply three rules:
- Compare voltages at the same reference point: Subtract the passive loop drop from the minimum voltage at the PoC injection point and compare the result directly against the camera's minimum coaxial input voltage—never raise the supply voltage above component ratings to compensate for cable resistance.
- Distinguish regulated steady-state operation from startup: Within a normal regulated operating range where the camera maintains approximately constant power consumption, input current follows IDC ≈ P / Vcam, so a lower input voltage increases current draw. Behavior during startup inrush, current limiting, or undervoltage shutdown cannot be extrapolated from that formula and must be checked separately.
- Check both per-port limits and total multi-camera power: On a multi-camera capture card, verify both the single-port PoC current limit and the card's total power supply capacity when all connected cameras run simultaneously.
Static harness routing vs. dynamic motion in robotics and machine vision
Beyond automotive vehicles, GMSL cameras are used in industrial machine vision, autonomous mobile robots (AMRs), and humanoid or articulated robots, with documented camera platforms from Basler and e-con Systems.

When selecting a coaxial assembly for industrial or robotic equipment, match the cable specification to the mechanical path:
- Static tie-down vs. continuous flexing: A cable fixed along a rigid frame experiences static bends and vibration, whereas a cable crossing a gantry carrier or robot joint undergoes repeated cyclic motion.
- Single-plane bending vs. multi-axis torsion: Drag chains bend the cable repeatedly along one axis, while robotic wrists and pan-tilt joints twist the coaxial shield and dielectric across multiple axes. Crushing, tight bends, or torsion can deform the coaxial geometry, shifting local impedance away from 50 Ω and fatiguing the shield.
- Verify explicit mechanical ratings: An "automotive" or "IP67" label does not prove drag-chain or torsion life. Do not use cables lacking dynamic flex data on moving joints (for moving applications, manufacturers such as Basler publish dedicated dynamic GMSL cable specifications). Equally, lacking dynamic ratings does not mean a cable is automatically suited for every static environment—always verify operating temperature, minimum static bend radius, and mated connector sealing for fixed installations.
Can passive coaxial cables be reused between GMSL and FPD-Link?
Analog Devices GMSL and Texas Instruments FPD-Link are incompatible active SerDes protocols; swapping a passive cable never allows a GMSL camera to communicate with an FPD-Link deserializer.
Because both ecosystems commonly use 50 Ω coaxial links with PoC (ADI UG-2212 Rev 3; TI SNLA224B), the same passive coaxial harness may be reused across systems only when it matches the target hardware's connector interfaces, pinout mapping, high-frequency channel budget, and PoC electrical limits, verified on the actual system.
Pre-order checklist
Before ordering a standard assembly or approving a custom harness drawing, confirm these items against your camera and capture card documentation:
- Endpoint interface: Exact housing series (
FAKRA,HFM,MATE-AX), mechanical keying code, and contact gender (Male/Plugvs.Female/Jack) at each end. - Topology & pinout: Direct
F-F, extensionM-F, or1-to-4quad breakout—plus the cavity-to-branch wiring diagram for any multi-port connector. - Channel & PoC margin: Per-lane series length (including breakout segments and couplings), attenuation/return-loss compliance at your link rate, passive DC loop resistance (Rcenter + Rshield + Rcontacts), and per-port plus total multi-camera current limits.
- Mechanical & environmental limits: Static vs. dynamic bend radius, temperature range, and mated sealing requirements.
Explore FAKRA cable assemblies and Mini FAKRA cable assemblies once you have defined both endpoints and the channel requirements.
