2500W 50A ZVS感应加热模块高频加热机熔化金属+48V线圈
$112.99
型号: EB0045761
80 销量
29 评论
有现货 商品库存
This induction heating circuit uses a 12-48V low-voltage DC power supply with a maximum current of 50A and a maximum power of 2500W. Continuous operation under conditions of good heat dissipation. Because of its moderate power, it can be used for DIY players to quench, annealing and other heat treatment of small parts. It can also be used with graphite crucible to smelt gold, silver, copper, aluminum and other metals. The heating is even and fast, very convenient.
Product parameters:
Product size: 240 x 120 x 105mm
Input voltage: 12V-48V recommended above 36V
Power requirements: less than 12V ≥ 20A 15V or more ≥ 30A
Maximum power: 2500W
Maximum current: 50A
Heater ring inner: 70mm (Recommended crucible + quartz suit, maximum support of 58mm crucible)
Recommended power: Product ID: 1279188
Heater ring inner: 70mm (Recommended crucible + quartz suit, maximum support of 58mm crucible)
Recommended power: Product ID: 1279188
Note:
1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.
2. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
3. When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 45A fuse or ammeter and air switch will be better. (package does not inclues)
4. Although this drive plate can withstand more than 50A current, but it is recommended that not exceed 48V 45A to prevent accidents and damage.
5. Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.
6. The minimum input voltage of the module is 12V, it doesn't mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same time conduction, will burn MOS tube;
7. If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.
8. Do not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn out
9. Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage decreases, below 12V is very dangerous
10. Induction heating power is great, so fever is normal, be sure to do a good job of cooling.
11. Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
11. Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
标签
感应加热模块
轻松支付
可信交付
- 商品详情
1 x PCB board
1 x 48V copper tube
If you want to buy 1000W 20A ZVS Induction Heating Machine: >>>Click here<<<
Update information: The old version of the cooling fan is powered directly from the motherboard through the buck module, and is now powered by the AC100-220V power adapter. (From April 9, 2019)
The new version is update to adds supporting water pump and supporting insulation sleeve for copper ring. (From November 22, 2019, CN warehouse)
Introduction:
This version is a 2500W upgrade of the 1800W ZVS heating module, using an oversized PCB layout design and an oversized heat sink for heat dissipation.
Good power, self-contained cooling fan interface, can also do Tesla discharge, mark generator, high voltage inverter power supply, etc.
This product can work continuously for several hours under good heat dissipation conditions.
包裹包括:
This product can work continuously for several hours under good heat dissipation conditions.
包裹包括:
1 x PCB board
1 x 48V copper tube
1 x PCB board
1 x 48V copper tube
- 商品评价
- 全部(29)
- 商品咨询
-
:Elecbee产品的起源在哪里?它们是否获得了认证?2023-03-03
-
店主回复:
Elecbee与中国的OEM工厂长期合作,以此来降低中间渠道成本,帮助您节省开支。我们的产品都是严格按照相关全球标准制作的,以确保产品具有良好的兼容性和卓越的品质。
2023-03-03
-
:您接受哪些付款方式?2023-03-03
-
店主回复:
我们的主要付款方式包括Paypal、信用卡、借记卡、银行转账等等,更多付款方式等待您的发现。请选取您喜欢的付款方式。
2023-03-03
-
:您何时安排发货?2023-03-03
-
店主回复:
在确认收到您的付款后,我们会尽快安排送货,并上传快递单号至网站,以供您跟踪。
2023-03-03
-
:如何进行退换货?2023-03-03
-
店主回复:
1.您可以在收到商品后的30天内申请退货。请确保外包装完好无损,产品保持原状。一旦我们收到包裹,根据相关规定安排退款。
2.退货流程:提交退货申请 - 审核通过退货申请 - 安排退货 - 收到商品并检查 - 我们安排退款。
3.对于因我们造成的退货,例如质量问题,我们将承担运费。对于由买家造成的退货,买家应负责运费。
2023-03-03
相关商品
品牌::
Elecbee
型号:: EB0045706
1000W 20A ZVS 低压感应加热线圈模块反激式驱动器加热器
规格:尺寸:约。 85 x 69 x 30 毫米最大电流:20A最大功率:1000W24V输入,空载电流3A48V输入,空载电流6A..
$13.99
+
-
品牌::
Elecbee
型号:: EB0045826
DC 12-36V 10A 300W ZVS线圈高压发电机驱动板放电反激模块
描述:输入直流12-36V(推荐24V)可用开关电源、铅酸电池或锂电池组供电,或变压器可用整流滤波供电,滤波电容不小于10000uF。 输出高压直流,电压约为输入电压的800倍。 12V的输入可以达..
$27.99
+
-
品牌::
Elecbee
型号:: EB0045964
4000W 85A ZVS高频感应加热板机带加热线圈水泵70ml坩埚
产品特点和功能:1、采用2mm厚PCB设计,铜厚2OZ,电流大,散热好;2. 180mm 220V散热风扇;3、加热线圈采用高温绝缘材料包裹,防止加热时短路,定制特定加热线圈;4、输入端采用大电流电源..
$243.00
+
-