ESP32 Thermal Camera Development Kit Lepton 3.0 Imaging Camera 6-Axis IMU MPU6886 Sensor Module
Product Features:
- 5V DC power supply
- USB Type-C
- ESP32-based
- Case Material: Nylon 3D print
- FLIR Lepton 3.0
- 4 MByte Flash
- 6-Axis IMU: MPU6886
- Microphone:SPM1423
- 2 Buttons, 1 Reset
- IPS LCD(1.14 inch)
- 2.4G Antenna: Proant 440
- 300 mAh Lipo Battery
- PMU: AXP192
- Dial encoder
- 4P PH2.0 Interface
- Wight: 26g
- Size: 48 * 30 * 29mm
ESP32 Features:
- 240 MHz dual core Tensilica LX6 microcontroller with 600 DMIPS
- Integrated 520 KB SRAM
- Integrated 802.11b/g/n HT40 Wi-Fi transceiver, baseband, stack and LWIP
- Integrated dual mode Bluetooth (classic and BLE)
- Hall sensor
- 32 kHz crystal oscillator
- PWM/timer input/output available on every GPIO pin
- SDIO master/salve 50MHz
Package Included:
- 1x M5StickT
- 1x USB Type-C(20cm)
Application:
- Car engine failure check
- Building dehumidification insulation sealing test
- Industrial furnace inner wall refractory crack
- Outdoor observation of animals at night
Usage:
Press the reset button to power on. The default display screen is RGB display mode. The left side is the temperature image, the upper right is the power display, and the lower right is the histogram and temperature range. The temperature range is automatically adjusted with the target temperature. The default bulls-eye automatically tracks the maximum temperature. Press the right button-A to switch the tracking mode (minimum / center / maximum value), press the button-B to switch the image display mode (GRAY / GOLDEN / RAINBOW / IRONBLACK / RGB). Dial encoder controls the display sensitivity (adjust the display temperature and color gamut), and long press the reset button for 6 seconds to turn off.
EasyLoader
Contact Sales
Your Name* | |
Your Email* | |
Topic* | |
Qty | |
Message | |
SUBMIT |
- Description
M5StickT is designed fully based on M5StickC, and the casing is 3D printed. Aiming for DIY use only. We didnt apply any certificates for this model. Pls consider whether it's OK to use in Japan. Thx!
Description:
M5StickT is an exquisite and compact infrared thermal imaging camera. It adopts the latest FLIR Lepton 3.0 long-wave infrared (LWIR) camera core with an effective resolution of 160 * 120 for a clear and stable image. As it is a large area non-contact infrared sensor, it is a good solution for temperature measurement. Its main control chip is Espressif’s ESP32, which has built-in support for Wi-Fi and Bluetooth connections, and computing speeds of up to 240Mhz. This provides a favorable guarantee for image output with a FPS reaching 7 and above. The screen is 1.14 inches and has a resolution of 135 * 240. The device comes with a rich variety of hardware resources: An on-board 6-axis Inertial Measurement Unit, a digital microphone and a power management chip and a built-in 300mAh battery, all embedded into the device. In terms of interactive operation, two programmable buttons and a rotary encoder are provided. In order to facilitate users to connect more peripherals, a 4 Pin PH2.0 interface with I2C support is provided at the bottom. The body is 3D printed from high quality Black Nylon filament. In addition, an M3 screw hole and a 1/4" screw hole are provided underside for easy mounting.
Lepton 3.0 Parameter
Effective Pixels | 160*120 |
Field of view | 56° |
Fast imaging time | < 500ms |
Effective Frame Rate | 8.7Hz |
Input Clock | 25MHz |
Pixel Size | 12μm |
Low operating power | 150 mW (operating), 650 mW (during shutter event), 5 mW (standby) |
Scene Dynamic Range | Low Gain Mode: -10 to 400°C; High Gain Mode: -10 to 140°C |
Spectral Range | 8 to 14µm |
Thermal Sensitivity | <50 mK(0.050°C) |
Optimum Temperature Range | -10°C to +80°C |
Notice:
M5StickT only supports WIN10 & Linux & MAC(<10.15) free drive, the rest of the operating system requires users to install the driver.
Installation steps: 1. Click the link below to download the driver installation package. 2. Connect the device and open the Computer Device Manager port option. 3. Right click on the unrecognized device and perform a manual update.
Driver download Link
PinMap:BUTTON A & BUTTON B
ESP32 GPIO37 GPIO39 BUTTON A Button Pin BUTTON B Button Pin IPS LCD
Driver IC: ST7789
Resolution: 135 * 240
ESP32 GPIO15 GPIO13 GPIO23 GPIO18 GPIO5 IPS LCD MOSI CLK DC RST CS PH2.0 PORT
ESP32 GPIO33 GPIO32 5V GND PH2.0 port SCL SDA 5V GND MIC (SPM1423)
ESP32 GPIO0 GPIO34 MICPHONE SCL SDA 6-Axis posture sensor (SH200Q/MPU6886) & power management IC (AXP192)
ESP32 GPIO22 GPIO21 6-Axis posture sensor SCL SDA power management IC SCL SDA AXP192
Microphone RTC TFT backlight TFT IC ESP32/3.3V MPU6886/SH200Q 5V GROVE LDOio0 LDO1 LDO2 LDO3 DC-DC1 IPSOUT Dial Encoder
STM32 PA2 PA3 PA4 Encoder SW EN_B EN_A Related Link:
- Reviews (29)
- All(29)
- Download
- Q & A
-
: Where is the origin of Elecbee products? Are they certificated?2023-03-03
-
Answer:
Elecbee has long-term cooperation agreements with the OEM factories in China. So that we are able to reduce the intermediate channel cost, and help you save money. Our products are all made strictly according to the relative global standard, to ensure the products have good compatibility and excellent quality.
2023-03-03
-
: What forms of payment do you accept?2023-03-03
-
Answer:
Our main payment methods include Paypal, Credit Cards, Debit Cards, Bank Transfer, and more to discover. Please choose the payment methods in your favor.
2023-03-03
-
: When will you arrange shipment?2023-03-03
-
Answer:
After confirming receipt of your payment. We will arrange the delivery as soon as possible and upload the courier number to the website for you to track.
2023-03-03
-
: How to exchange or return?2023-03-03
-
Answer:
1. You can apply to return within 30 days after receipt of the goods. Please make sure the outside package is intact, and the product is in its original condition. We will arrange your refund according to the relevant provisions once the package is received.
2. Return process: You Apply for a Return - Approve the Return - Arrange a Return - Receive the Products and make Inspection - We arrange a Refund;
3. We will bear the freight charges for returns caused by us, for instance, the quality problem. As to returns caused by the buyer, the buyer should be responsible for the shipping fee.
2023-03-03
Related Products
MH-Z19B Upgrade Version 0-5000PPM Infrared CO2 Sensor For CO2 Indoor Air Quality Monitor UART/PWM
Description: Product Model: MH-Z19B (please note that this item is not winsen brand.)Color: Gol..
TEC1-12715 Thermoelectric Cooler Peltier 40*40MM 12V Peltier Refrigeration Module Semiconductor Refrigeration Sheet
1 x TEC1-12715 Thermoelectric Cooler Peltier..
HCS-LTS06A LTS06NP TBC06DS5 Hall Current Sensor Holzer Closed Loop Current Sensor
>>>Manual: Click here to open..
Smart Car Obstacle Avoidance Sensor Measuring Distance Infrared Sensor Photoelectric Switch Module
1 x Smart Car Avoidance Sensor Module..